Carrier Access Adit 600 User Manual Download Page 244

Page: 244 / 296

11-18

CMG Router - Release 2.7

Router Configuration

Back-to-Back with Multi-Link PPP

Back-to-Back with Multi-Link PPP

The following configuration will set up two Adit 600 Routers back-to-back with Multi-
Link PPP.

Boulder Router in Slot 1

Command

Description

set 1 default

Set Router to default settings

disconnect a:1

Disconnect all connections to the T1 on the
Controller (slot a)

disconnect 1

Disconnect all connections to the router in slot 1

set a:1:all type data

Set the T1-1 of the Controller, Type to Data

connect a:1:all 1:1:1

Connect all of T1-1 to the Router that is in slot 1

connect a:2:all 1:1:2

Connect all of T1-1 to the Router that is in slot 1

rename 1 "LocalUnit" "Boulder"

Rename the Adit 600 from "LocalUnit" (default)
to "Boulder" (LAN)

rename 1 "LocalUnit" "Boulder"

Rename the Adit 600 from "LocalUnit" (default)
to "Boulder" (LAN)

set 1:1:1-2 multilink group 1

Rename the Adit 600 from "LocalUnit" (default)
to "Boulder" (LAN)

rename 1 "RemoteUnit" "wan1"

Rename WAN #1 from "RemoteUnit" (default) to
"wan1"

set 1:1 ip address 1.1.1.1
255.255.255.0

Set the Ethernet IP address, in the conventional IP
address format. (Router LAN)

add 1 "wan1" static ip network
2.2.2.0 255.255.255.0 1

Adds a static IP network (route) to the WAN
interface

set 1 "wan1" trunk multilink
group 1

Set the WAN interface named "wan1" to be
mapped to trunk multilink group 1

reset 1

Reboot the router, to enable all configurations set

Summary of Contents for Adit 600









































































































































































































































































































Search results

Summary of Contents for Adit 600

Reviews:

Related manuals for Adit 600

Brands by name

Popular brands

Carrier Access Adit 600, User Manual

Search results

Summary of Contents for Adit 600

Reviews:

Related manuals for Adit 600

Brands by name

Popular brands