CarpeStar SMG Series User Manual Download Page 65

Page: 65 / 139

Page 59

enabled.

FWD on

Unreachable

Sets whether to enable the feature of FWD on unreachable and the FWD number if

it is enabled.

FWD Setting Status

Displays the setting status of the call forwarding service.

FWD Query Status

Displays the query status of the FWD settings. This configuration is unavailable for

CDMA module.

Cancel All

Cancels all the setting on call FWD service. This item will appear if none of the call

FWD is selected.

Click

Modify

in Figure 3-57 to modify the properties of the corresponding port. See Figure 3-58 for

the call forwarding modification interface. Then click

Modify

to save the settings into the gateway.

It will take some time to apply the settings, and you can check the result in the

„FWD Setting

Status

‟ column. Click

Reset

to restore the configurations, or click

Cancel

to cancel the settings.

Figure 3-58 Wireless Service Modification Interface

3.6.4 Short Message

Series

Wireless

Gateway

User

Manual

(Version

1.9.0)

Summary of Contents for SMG Series












































































































































Search results

Summary of Contents for SMG Series

Reviews:

Related manuals for SMG Series

Brands by name

Popular brands

CarpeStar SMG Series, User Manual

Search results

Summary of Contents for SMG Series

Reviews:

Related manuals for SMG Series

Brands by name

Popular brands