CarpeStar SMG Series User Manual Download Page 61

Page: 61 / 139

Page 55

Note:

1, This configuration item is unsupported when the DTMF send mode is set to

Remote Transmission;

2, This configuration item is unsupported for the CDMA gateway.

Duration at ON

Sets the duration of the DTMF signal at ON state, calculated by ms. The default

value is 120.

Duration at OFF

Sets the duration of the DTMF signal at OFF state, calculated by ms. The

default value is 100.

Disconnect Voice while

Sending DTMF

Sets whether to disconnect the voice channel while sending the DTMF, with the

default value of

Note: This configuration item is unsupported when the DTMF send mode is set

to Remote Transmission;

GSM (WCDMA/CDMA/LTE)

DTMF Receive Mode

Sets the mode to receive the GSM (WCDMA/CDMA/LTE) DTMF, two options

available: Chip Receive and Wireless Module Receive. The default values for

GSM WCDMA and LTE are

Wireless Module Receive;

the default value for

CDMA is

Chip Receive

DTMF Voltage Detection for

GSM

Set the On and off of the DTMF detection for GSM.

Network Scan Mode

Sets a network for the call, three options available for the WCDMA gateway:

Automatic, GSM Only and WCDMA Only. The default value is

Automatic

. Nine

options are available for the LTE gateway: Automatic, GSM Only, WCDMA Only,

LTE Only, TD-SCDMA Only, UMTS Only, CDMA Only, HDR Only, CDMA and

EVDO Only. The default value is

Automatic

Network Scan Sequence

Sets the priority of the network, three options available for the WCDMA

gateway:

Automatic

GSM prior to WCDMA

and

WCDMA prior to GSM

. The

default value is

Automatic.

Only the option Automatic is available for the LTE

gateway.

SMS Sending Interval

Sets the interval to send SMS for each port. Range of value: 1~60, with the

default value of

Maximum Pieces of Saved

Logs

Sets the amount of the logs to be saved for each port. Range of value: 50~500,

with the default value of

100

SMS Receipt

Once this feature is enabled, the gateway will receive a receipt upon the remote

side receiving the SMS.

Note: This configuration item is unsupported for the CDMA gateway.

AT Command Mode

Sets the AT command sent with the call forwarding. There are two options

available: CCFC command mode and ATD command mode. The GSM

gateways support both modes, while the WCMDA/LTE gateways only support

the CCFC command mode and the CDMA gateways only support the ATD

command mode.

Set/Cancel Service Number for

FWD Unconditionally,

Set/Cancel Service Number for

FWD on Busy, Set/Cancel

Sets or Cancels the service No. for FWD unconditionally, FWD on busy, FWD

on no reply or FWD Unreachable. The former box is used to set the service No,

while the latter one is to cancel the service No,.

CMG

Series

Wireless

Gateway

User

Manual

(Version

1.9.0)

Summary of Contents for SMG Series












































































































































Search results

Summary of Contents for SMG Series

Reviews:

Related manuals for SMG Series

Brands by name

Popular brands

CarpeStar SMG Series, User Manual

Search results

Summary of Contents for SMG Series

Reviews:

Related manuals for SMG Series

Brands by name

Popular brands