CarpeStar SMG Series User Manual Download Page 25

Page: 25 / 139

Page 19

refresh the count of SIP messages, or click

Clear

to clear the current count of SIP messages.

3.3 Quick Config

Figure 3-10 Quick Config Interface

See Figure 3-10 for the Quick Config interface. Follow the gateway Quick Configuration wizard
and you can easily complete the settings on network, SIP and Port. The gateway can work
normally after configuration.

See Figure 3-11 for the Quick Config-Network Settings interface. Refer to

3.5.1 Network

for

detailed settings. After configuration, click

Next

to enter the SIP Settings interface.

Figure 3-11 Quick Config-Network Settings Interface

See Figure 3-12 for the Quick Config-SIP Settings interface. The configuration items on this
interface are the same as those on

the SIP interface. Refer to

3.4.1 SIP

for detailed settings. You

are required to fill with the information about the registrar if the gateway must be registered. After
configuration, click

Back

to go back to the Network Settings interface; click

Next

to enter the Port

Settings interface.

Series

Wireless

Gateway

User

Manual

(Version

1.9.0)

Summary of Contents for SMG Series












































































































































Search results

Summary of Contents for SMG Series

Reviews:

Related manuals for SMG Series

Brands by name

Popular brands

CarpeStar SMG Series, User Manual

Search results

Summary of Contents for SMG Series

Reviews:

Related manuals for SMG Series

Brands by name

Popular brands