CarpeStar SMG Series User Manual Download Page 99

Page: 99 / 139

Page 93

The table below explains the items in the above figure.

Item

Description

Index

The unique index of each port group, which is mainly used in the configuration of

routing rules and number manipulation rules to correspond to port groups.

Description

More information about each port group, with default value of

default

Register Port Group

To register the port group to the SIP server. Only when this configuration item is set

Yes

can you see the configuration items

SIP Account

and

Password

SIP Account

When the port group initiates a call to SIP, this item corresponds to the username of

SIP.

Password

Registration password of the port group. To register the port group to the SIP server,

both configuration items

SIP Account

and

Password

should be filled in.

Authentication

Username

Authentication username of a port, used to register the port to the SIP server when

IMS network is enabled.

Note: This item appears only when IMS Network is enabled.

Server Index

The index of the sip server which will be quoted by the current port.

Authentication

Mode

Sets the way for SIP to make outgoing calls (Tel



IP) on the gateway.

Option

Description

Do Not Register

(default)

SIP initiates a call in a point-to-point mode.

Register Port Group

SIP initiates a call with the registered SIP account and

password of the port group.

Register Port

SIP initiates a call with the registered SIP account and

password of the port.

Register Status

Registration status of the port group. See Figure 3-109. When

Register Port

Group

is set to

, the value of this item is

Unregistered

; when

Register Port

Group

is set to

Yes

, the value of this item may be

Failed

Registered

Series

Wireless

Gateway

User

Manual

(Version

1.9.0)

Summary of Contents for SMG Series












































































































































Search results

Summary of Contents for SMG Series

Reviews:

Related manuals for SMG Series

Brands by name

Popular brands

CarpeStar SMG Series, User Manual

Search results

Summary of Contents for SMG Series

Reviews:

Related manuals for SMG Series

Brands by name

Popular brands