CarpeStar SMG Series User Manual Download Page 33

Page: 33 / 139

Page 27

Figure 3-19 Add New SIP Station

The table below explains the items shown above:

Item

Description

Number

The logical number for a SIP station to register to the gateway.

Username

The username used to register a SIP station to the gateway.

Password

The password used to register a SIP station to the gateway.

Bound Port

The wireless port which is bound to the SIP station.

Description

It is user-defined, with the default value of

default

Batch Setting

Used to set multiple SIP stations at the same time.

After configuration, click

Save

to save the above settings into the gateway or click

Close

to cancel

the settings. See Figure 3-20 for the applied SIP station information.

Figure 3-20 SIP Station Interface

Click

Modify

in the above figure to modify the configuration of the SIP station. See Figure 3-21.

The configuration items on this interface are the same as those on the

Add New SIP Station

interface.

Series

Wireless

Gateway

User

Manual

(Version

1.9.0)

Summary of Contents for SMG Series












































































































































Search results

Summary of Contents for SMG Series

Reviews:

Related manuals for SMG Series

Brands by name

Popular brands

CarpeStar SMG Series, User Manual

Search results

Summary of Contents for SMG Series

Reviews:

Related manuals for SMG Series

Brands by name

Popular brands