CarpeStar SMG Series User Manual Download Page 85

Page: 85 / 139

Page 79

Figure 3-94 Port Timing Setting Interface

The table below explains the configuration items shown in the above figure:

Item

Description

Port

The number of the port corresponding to the wireless module.

Unit

Sets the timing unit for the call

，

eight options available: 1s, 5s, 10s, 20s, 30s,

40s, 50s and 60s. The actual call time will be calculated as the integral multiple

of the setting time. Take an example: supposed the setting time is 30s and the

actual call time is 72s, thus, the gateway will consider the call time as 90s.

Time Limit on a Single

Call

Sets whether to enable the time limit on a single call.

Max Call Time

Sets the maximum time length of a call.

Series

Wireless

Gateway

User

Manual

(Version

1.9.0)

Summary of Contents for SMG Series












































































































































Search results

Summary of Contents for SMG Series

Reviews:

Related manuals for SMG Series

Brands by name

Popular brands

CarpeStar SMG Series, User Manual

Search results

Summary of Contents for SMG Series

Reviews:

Related manuals for SMG Series

Brands by name

Popular brands