CarpeStar SMG Series User Manual Download Page 31

Page: 31 / 139

Page 25

from

from

“

Request

” Field

. The default value is

“

Request

” Field

Set CallerID Position

There are two options to set the position of the calling party number:

“Displayname

of From Field

” and “Username of From Field”. The default value is “

Username of

From Field

”.

Obtain CallerID from

There are two optional ways to obtain the calling party number: from

“Displayname

of From Field

” and from “Username of From Field”. The default value is “

Username

of From Field

”.

Use Contact

Address

Sets whether to send the request message according to the content of Contact, with

the default setting of

disabled

. As it is disabled, if the Contact field indicates an IP

address within the LAN, the request message will be sent according to the source

address; if the Contact field indicates an IP address belonging to the WAN, the

request message will be sent according to this IP address.

Reply To Source

Address

Once this feature is enabled, the gateway will reply the source address in the invite

message. As the item

Use Contact Address

conflicted with this item, you may now

shield the other one while enabling one of them.

Two Stage Dialing

for SIP Incoming

Call

Once this feature is enabled, the incoming call from SIP should perform the two

stage dialing operation. By default this feature is disabled.

Maximum Wait

Answer Time

Sets the maximum time for the SIP channel to wait for the answer from the called

party of the outgoing call it initiates. If the call is not answered within the specified

time period, it will be canceled by the channel automatically. The default value is 60,

calculated by s.

SIP Station

Supported

Once this feature is enabled, a SIP terminal can be registered to the gateway to

become a SIP station. By default this feature is disabled.

Set SIP Identifying

Sets the SIP identifying content in the SIP call message. The default setting is

Gateway

Maximum Wait RTP

Time

Sets the maximum time for the SIP channel to wait for the RTP packet. If no RTP

packet is received within the specified time period, the channel will enter the

pending state automatically and release the call. The default value is

（

disabled

）

calculated by s.

Ignore ACK

Once this feature is enabled, it is not necessary for the gateway to wait for the ACK

message after sending the 200OK message to establish a call. By default it is

disabled

Iptable for SIP Calls

Only some special SIP messages, which can be configured by users, are allowed to

send to the gateway.

SIP Encryption

Once this feature is enabled, you can encrypt the SIP signal following selecting an

encryption criterion and setting a key. By default it is

disabled

Encryption Criterion

The criterion used to encrypt the SIP signal. At present only VOS1.1 is supported.

Identifier

The identifier field of the VOS encryption, which is used to obtain the key of the SIP

encryption.

Key

The key to encrypt the SIP signal.

RTP Encryption

Once this feature is enabled, you can encrypt the RTP package. By default it is

disabled

Series

Wireless

Gateway

User

Manual

(Version

1.9.0)

Summary of Contents for SMG Series












































































































































Search results

Summary of Contents for SMG Series

Reviews:

Related manuals for SMG Series

Brands by name

Popular brands

CarpeStar SMG Series, User Manual

Search results

Summary of Contents for SMG Series

Reviews:

Related manuals for SMG Series

Brands by name

Popular brands