CarpeStar SMG Series User Manual Download Page 95

Page: 95 / 139

Page 89

Figure 3-107 Port Modification

The table below explains the configuration items on the port modification interface.

Item

Description

Port

Serial number of the port on the device.

Register Port

Sets whether to register the port to the SIP server.

When this item is set to

, the item

Reg Status

on the Port Settings interface (Figure

3-106) shows

Unregistered

; when this item is set to

Yes

, the item

Reg Status

shows

Failed or Registered.

SIP Account

When the port initiates a call to SIP, this item corresponds to the username of SIP. The

default SIP account is 80XX among which XX represents the corresponding port

number. For example, the default SIP account corresponding to Port 1 is 8001, and

that corresponding to Port 8 is 8008.

Password

Registration password of the port. To register a port to the SIP server, both items

SIP

Account

and

Password

must be filled in.

Series

Wireless

Gateway

User

Manual

(Version

1.9.0)

Summary of Contents for SMG Series












































































































































Search results

Summary of Contents for SMG Series

Reviews:

Related manuals for SMG Series

Brands by name

Popular brands

CarpeStar SMG Series, User Manual

Search results

Summary of Contents for SMG Series

Reviews:

Related manuals for SMG Series

Brands by name

Popular brands