CarpeStar SMG Series User Manual Download Page 32

Page: 32 / 139

Page 26

Abnormal Call

Hangup Detection

Sets the interval between checks of the remote end‟s abnormal hangup, with the

default value of 0 (feature disabled), calculated by s. It is suggested to set to 10s if

this feature is necessary to be used.

Server Status

Detection

The interval of sending a heartbeat packet to detect the master registrar server

status, with the default value of 0 (feature disabled), calculated by s. It is suggested

to set to 15s if this feature is necessary to be used.

Available Port

Negotiation

When this feature is enabled, the gateway will send messages to the preset

negotiation server (e.g. VOS server) to let it know the number of available ports on

the gateway. By default this feature is disabled.

Cycle, Address

Cycle means how soon will the gateway send a message; Address indicates the

server address (e.g. VOS server).

Occasion to Reply

183

Sets the occasion to reply the 183 message. Two options including: Immediately

and After ringing, with the default value of

Immediately

Occasion to Reply

200 Ok

Sets the occasion to reply 200 OK. Two options including: After pickup and After

ringing, with the default value of

After pickup

3.4.3 SIP Station

A SIP terminal can be registered to the gateway to become a SIP station. Tick the option of

„

SIP

Station Supported

‟ on

3.4.2 SIP Compatibility

interface, and you will see the item SIP Station on

the VoIP Settings menu. Click

„

SIP Station

‟ to go into the SIP Station interface. By default, there is

no available SIP station. See Figure 3-18 below.

Figure 3-18 SIP Station Setting Interface

Click

Add New

to add SIP stations manually. See Figure 3-19. You can configure basic SIP

station information on this interface. The bound port to a SIP station must be a wireless port and
unique. The username must be the same as that used to register the SIP terminal to the gateway.

Series

Wireless

Gateway

User

Manual

(Version

1.9.0)

Summary of Contents for SMG Series












































































































































Search results

Summary of Contents for SMG Series

Reviews:

Related manuals for SMG Series

Brands by name

Popular brands

CarpeStar SMG Series, User Manual

Search results

Summary of Contents for SMG Series

Reviews:

Related manuals for SMG Series

Brands by name

Popular brands