Canon lpb3360 User Manual Download Page 268

Page: 268 / 338

8-31

oub

leshooting

Message List

<30 MEMORY FULL>

Cause

The work memory has run out while the system is processing the data.

Remedy

The printer continues printing by pressing the

(Online) key. However, the

data with which an error has occurred may not be printed properly.

<32 2-SIDED ERROR>

Cause

The printer received 2-sided printing data of paper sizes (including the
orientation) or paper types unavailable for automatic 2-sided printing.

Remedy 1 The printer continues printing by pressing the

(Online) key. However, the

data on each side is printed on two pages.

Remedy 2 After performing a soft reset in the RESET menu, change the setting to a paper

size or type available for automatic 2-sided printing, and then print again.

<33 WORK MEM.FULL>

Cause

The work memory for each operation mode cannot be secured.

Remedy 1 The printer continues printing by pressing the

(Online) key. However, the

data with which an error has occurred is not printed properly.

IMPORTANT

When you continue printing by pressing the

(Online) key, be aware that the data of

macro that is already registered may be deleted.

Remedy 2 Perform a soft reset in the RESET menu, increase the free space of RAM using

the following procedure, and then print again.

•

Perform a hard reset or cycle the power of the printer (Be aware that all the
data in the memory that the printer has received will be deleted).

<35 TABLE FULL>

Cause

The number of the documents in a job has exceeded 16.

Remedy

The printer continues printing by pressing the

(Online) key. However, the

job with which an error has occurred is not printed.

<38 LOW IMGE QLTY>

Cause

The printer cannot process the data because it is too complicated.

Remedy 1 The printer continues printing by pressing the

(Online) key. However, the

printer prints with the image quality level being lowered.

Downloaded from ManualsPrinter.com Manuals

Summary of Contents for lpb3360



















































































































































































































































































































































Search results

Summary of Contents for lpb3360

Reviews:

Brands by name

Popular brands

Canon lpb3360, User Manual

Search results

Summary of Contents for lpb3360

Reviews:

Brands by name

Popular brands