Canon imageRUNNER ADVANCE 6075 Series, Service Manual

Page: 930 / 1406

8
8
8-148
8-148
Service Mode > COPIER > OPTION > NETWORK
Service Mode > COPIER > OPTION > NETWORK
COPIER > OPTION > NETWORK
WUEV-RTR Setting of sleep notification range
Lv.2 Details To set the number of available routers to the target for sleep
notification.
Use case Upon user’s request
Adj/set/operate method 1) Enter the setting value, and then press OK key.
2) Turn OFF/ON the main power switch.
Caution This is active when COPIER> OPTION> NETWORK> WUEV-SW is
set to 0: Notified.
Display/adj/set range 0 to 254
Default value 3
Related service mode COPIER> OPTION> NETWORK> WUEV-SW
WUEN-LIV Recovery time setting after sleep notice
Lv.2 Details To set the time from the sleep start from network without job
assignment until the mode is shifted to the sleep mode.
Use case When setting the startup time after sleep notification
Adj/set/operate method 1) Enter the setting value, and then press OK key.
2) Turn OFF/ON the main power switch.
Display/adj/set range 10 to 600
Unit 1 second
Default value 15
DHCP-12 ON/OFF of DHCP-option 12 request
Lv.2 Details To set ON/OFF of inquiry on the host name (Option 12) which uses
Option 55 of DHCP.
Selecting OFF can prevent DHCP packet from including Option 12 or
Option 81under the packet-monitoring network environment.
Use case Upon user’s request
Adj/set/operate method 1) Enter the setting value, and then press OK key.
2) Turn OFF/ON the main power switch.
Display/adj/set range 0 to 1
0: OFF, 1: ON
Default value 1
Supplement/memo DHCP: Dynamic Host Configuration Protocol
COPIER > OPTION > NETWORK
DHCP-81 ON/OFF IPaddress dynamic chng in DHCP-81
Lv.2 Details To set ON/OFF for dynamic change of IP address by Option 81 of
DHCP.
Selecting OFF can prevent DHCP packet from including Option 12 or
Option 81under the packet-monitoring network environment.
Selecting ON enables dynamic change of IP address by Option 81 of
DHCP in the case that the dynamic DNS setting is ON in user mode.
Use case Upon user’s request
Adj/set/operate method 1) Enter the setting value, and then press OK key.
2) Turn OFF/ON the main power switch.
Caution Be sure to set ON for the dynamic DNS setting in user mode to
enable dynamic change of IP address.
Display/adj/set range 0 to 1
0: OFF, 1: ON
Default value 1
Supplement/memo DHCP: Dynamic Host Configuration Protocol
IFX-CHIG Set operation by IFAX recv mail content
Lv.1 Details To set the number of characters for the IFAX received mail content,
so that the mail is not printed/forwarded when the characters in the
text is less than the number of specified characters.
This machine can output blank paper because some senders send
e-mail text consists of linefeed codes only. In such case, specify 2
(number of characters) so that there will be no output of blank paper.
In the case of specifying any number other than 0, header/footer is
printed/forwarded in 1 sheet only if the e-mail (body) text is less than
the specified value while no TIFF file is attached.
As the value is incremented by 1, the number of target characters in
e-mail body text is increased by 1 character.
Use case When reducing print of blank paper due to e-mail received by IFAX
Adj/set/operate method 1) Enter the setting value, and then press OK key.
2) Turn OFF/ON the main power switch.
Caution Be sure to get approval from the user by telling that there will be no
print of e-mail (body) text if the number of characters is less than the
specified value.
Display/adj/set range 0 to 999
0: E-mail (body) text is not ignored.
Unit 1 character
Default value 0
Supplement/memo 1 Japanese Kanji character is calculated as 2 bytes, and the control
codes (such as linefeed code, etc) are included in the number of
characters.