Canmax Technology CM-2D002 Page 41 User Manual Download

Page: 41 / 240

PROGRAM THE INTERFACE

2-8-7 ACK/NAK

After transmitting data, the scan engine waits for an ACK character (hex 06) or

a NAK character (hex 15) response from the host. If ACK is received, the

communications cycle is completed and the scan engine looks for more bar

codes. If NAK is received, the last set of bar code data is retransmitted and the

scan engine waits for ACK/NAK again. Turn on the ACK/NAK protocol by

scanning the ACK/NAK On bar code below. To turn off the protocol, scan

ACK/NAK Off.

Default = ACK/NAK Off

ACK/NAK ON

ACK/NAK OFF

2-8-8 RS232 Stop Mode

Scan the following bar code to force the engine into a stop mode. Restart the

engine by using a trigger pull, nWake, or RxD toggle.

RS232 Stop Mode On

2-8-7 ACK/NAK

2-8-8 RS232 Stop Mode

Summary of Contents for CM-2D002
















































































































































































































































Search results

Summary of Contents for CM-2D002

Reviews:

Related manuals for CM-2D002

Brands by name

Popular brands

Canmax Technology CM-2D002, User Manual

Search results

Summary of Contents for CM-2D002

Reviews:

Related manuals for CM-2D002

Brands by name

Popular brands