Canmax Technology CM-2D002 User Manual Download

Page: 55 / 240

INPUT/OUTPUT SETTINGS

3-7 Character Deactivation Mode

If you have sent a character from the host to trigger the scanner to begin

scanning, you can also send a deactivation character to stop scanning. Scan

the following On bar code to use character deactivation, then use Deactivation

Character (following) to select the character you will send from the host to

terminate scanning.

Default = Off

Off

3-7-1 Deactivation Character

This sets the character used to terminate scanning when using Character

Deactivation Mode. On the

ASCII Conversion Chart (Code Page 1252)

, find

the hex value that represents the character you want to use to terminate

scanning. Scan the following bar code, then use the

Programming Chart

inside

the back cover of this manual to read the alphanumeric combination that

represents that ASCII character. Scan Save

to finish.

Default = 14 [DC4]

Deactivation Character

3-7 Character Deactivation Mode

3-7-1 Deactivation Character

Summary of Contents for CM-2D002
















































































































































































































































Search results

Summary of Contents for CM-2D002

Reviews:

Related manuals for CM-2D002

Brands by name

Popular brands

Canmax Technology CM-2D002, User Manual

Search results

Summary of Contents for CM-2D002

Reviews:

Related manuals for CM-2D002

Brands by name

Popular brands