Canmax Technology CM-2D002 Page 129 User Manual Download

Page: 129 / 240

129

SYMBOLOGIES

Off

6-12-5 Code 128 Code Page

Code pages define the mapping of character codes to characters. If the data

received does not display with the proper characters, it may be because the

bar code being scanned was created using a code page that is different from

the one the host program is expecting. If this is the case, scan the bar code

below, select the code page with which the bar codes were created (see

ISO

2022/ISO 646 Character Replacements

), and scan the value and the Save

barcode from the

Programming Chart

on the inside the back cover of this

manual. The data characters should then appear properly.

Code 128 Code Page

6-13 GS1-128

Default All GS1-128 Settings

6-13-1 GS1-128 On/Off

6-12-5 Code 128 Code Page

6-13 GS1-128

6-13-1 GS1-128 On/Off

Summary of Contents for CM-2D002
















































































































































































































































Search results

Summary of Contents for CM-2D002

Reviews:

Related manuals for CM-2D002

Brands by name

Popular brands

Canmax Technology CM-2D002, User Manual

Search results

Summary of Contents for CM-2D002

Reviews:

Related manuals for CM-2D002

Brands by name

Popular brands