Canmax Technology CM-2D002 User Manual Download

Page: 61 / 240

INPUT/OUTPUT SETTINGS

3-10 CodeGate

When CodeGate is On, the trigger is used to allow decoded data to be

transmitted to the host system. The scanner remains on, scanning and

decoding bar codes, but the bar code data is not transmitted until the trigger is

pressed. When CodeGate is Off, bar code data is transmitted when it is

decoded.

Default = CodeGate Off Out-ofStand

CodeGate Off Out-of-Stand

CodeGate On Out-of-Stand

3-11 Mobile Phone Read Mode

When this mode is selected, your scanner is optimized to read bar codes from

mobile phone or other LED displays. However, the speed of scanning printed

bar codes may be slightly lower when this mode is enabled.

Hand Held Scanning – Mobile Phone

Presentation Scanning - Mobile Phone

Note

: To turn off Mobile Phone Read Mode, scan a Manual or Serial Trigger

3-10 CodeGate

3-11 Mobile Phone Read Mode

Summary of Contents for CM-2D002
















































































































































































































































Search results

Summary of Contents for CM-2D002

Reviews:

Related manuals for CM-2D002

Brands by name

Popular brands

Canmax Technology CM-2D002, User Manual

Search results

Summary of Contents for CM-2D002

Reviews:

Related manuals for CM-2D002

Brands by name

Popular brands