Canmax Technology CM-2D002 Page 39 User Manual Download

Page: 39 / 240

PROGRAM THE INTERFACE

2-8-4 RS232 Handshaking

RS232 Handshaking allows control of data transmission from the scan engine

using software commands from the host device. When RTS/CTS is turned Off,

no data flow control is used.

Flow Control, No Timeout

: The scan engine asserts RTS when it has data to

send, and will wait indefinitely for CTS to be asserted by the host.

Two-Direction Flow Control

: The scan engine asserts RTS when it is OK for

the host to transmit. The host asserts CTS when it is OK for the device to

transmit.

Flow Control with Timeout

: The scan engine asserts RTS when it has data to

send and waits for a delay (see

RS232 Timeout

) for CTS to be asserted by the

host. If the delay time expires and CTS is not asserted, the device transmit

buffer is cleared and scanning may resume.

Default = RTS/CTS Off

Flow Control, No Timeout

Two-Direction Flow Control

Flow Control with Timeout

RTS/CTS Off

2-8-4 RS232 Handshaking

Summary of Contents for CM-2D002
















































































































































































































































Search results

Summary of Contents for CM-2D002

Reviews:

Related manuals for CM-2D002

Brands by name

Popular brands

Canmax Technology CM-2D002, User Manual

Search results

Summary of Contents for CM-2D002

Reviews:

Related manuals for CM-2D002

Brands by name

Popular brands