Canmax Technology CM-2D002 User Manual Download

Page: 135 / 240

135

SYMBOLOGIES

6-15 UPC-A/EAN-13 with Extended Coupon

Use the following codes to enable or disable UPC-A and EAN-13 with

Extended Coupon Code. When left on the default setting (Off), the scanner

treats Coupon Codes and Extended Coupon Codes as single bar codes.

If you scan the

Allow Concatenation code

, when the scanner sees the

coupon code and the extended coupon code in a single scan, it transmits both

as one symbology. Otherwise, it transmits the first coupon code it reads.

If you scan the

Require Concatenation code

, the scanner must see and read

the coupon code and extended coupon code in a single read to transmit the

data. No data is output unless both codes are read.

Default = Off

Off

Allow Concatenation

Require Concatenation

6-15 UPC-A/EAN-13 with Extended Coupon
Code

Summary of Contents for CM-2D002
















































































































































































































































Search results

Summary of Contents for CM-2D002

Reviews:

Related manuals for CM-2D002

Brands by name

Popular brands

Canmax Technology CM-2D002, User Manual

Search results

Summary of Contents for CM-2D002

Reviews:

Related manuals for CM-2D002

Brands by name

Popular brands