Canmax Technology CM-2D002 User Manual Download Page 188

Page: 188 / 240

188

UTILITIES

7-6 Resetting the Factory Defaults

Caution

: This selection erases all your settings and resets the scan

engine to the original factory defaults. It also disables all plugins.

If you aren’t sure what programming options are in your scan engine, or you’ve

changed some options and want to restore the scan engine to factory default

settings, first scan the Remove Custom Defaults bar code, then scan Activate

Defaults.

This resets the scan engine to the factory default settings.

Remove Custom Defaults

Activate Defaults

The

Menu Commands,

list the factory default settings for each of the

commands (indicated by an asterisk (*) on the programming pages).

7-6 Resetting the Factory Defaults

Summary of Contents for CM-2D002
















































































































































































































































Search results

Summary of Contents for CM-2D002

Reviews:

Brands by name

Popular brands

Canmax Technology CM-2D002, User Manual

Search results

Summary of Contents for CM-2D002

Reviews:

Brands by name

Popular brands