Canmax Technology CM-2D002 User Manual Download Page 44

Page: 44 / 240

INPUT/OUTPUT SETTINGS

3-1 Power Up Beeper

The scan engine can be programmed to beep when it’s powered up.

Scan the Off bar code(s) if you don’t want a power up beep.

Default = Power Up Beeper On Scanner

Power up Beer off scanner

Power up Beer on Scanner

3-2 Beep on BEL Character

You may wish to force the scan engine to beep upon a command sent from the

host. If you scan the Beep on BEL On barcode below, the scan engine will

beep every time a BEL character is received from the host.

Default = Beep on BEL Off

Beep on BEL off

Beep on BEL on

3-1 Power Up Beeper

3. INPUT/OUTPUT SETTINGS

3-2 Beep on BEL Character

Summary of Contents for CM-2D002
















































































































































































































































Search results

Summary of Contents for CM-2D002

Reviews:

Brands by name

Popular brands

Canmax Technology CM-2D002, User Manual

Search results

Summary of Contents for CM-2D002

Reviews:

Brands by name

Popular brands