Canmax Technology CM-2D002 User Manual Download

Page: 97 / 240

DATA FORMATTING

5-5 Data Formatter

When Data Formatter is turned Off, the bar code data is output to the host as

read, including prefixes and suffixes.

Data Formatter Off

You may wish to require the data to conform to a data format you have created

and saved. The following settings can be applied to your data format:

• Data Formatter On, Not Required, Keep Prefix/Suffix

Scanned data is modified according to your data format, and prefixes and

suffixes are transmitted.

• Data Format Required, Keep Prefix/Suffix

Scanned data is modified according to your data format, and prefixes and

suffixes are transmitted. Any data that does not match your data format

requirements generates an error tone and the data in that bar code is not

transmitted. If you wish to process this type of bar code without generating an

error tone, see

Primary/Alternate Data Formats

Choose one of the following options.

Default = Data Formatter On, Not Required, Keep Prefix/Suffix

Data Formatter On, Not Required,

Keep Prefix/Suffix

Data Format Required, Keep

Prefix/Suffix

5-5 Data Formatter

Summary of Contents for CM-2D002
















































































































































































































































Search results

Summary of Contents for CM-2D002

Reviews:

Related manuals for CM-2D002

Brands by name

Popular brands

Canmax Technology CM-2D002, User Manual

Search results

Summary of Contents for CM-2D002

Reviews:

Related manuals for CM-2D002

Brands by name

Popular brands