Canmax Technology CM-2D002 Page 67 User Manual Download

Page: 67 / 240

INPUT/OUTPUT SETTINGS

Off(No display)

3-18-1 User-Specified Aimer Delay

If you want to set your own length for the duration of the delay, scan the bar

code below, then set the time-out by scanning digits (0 - 4,000 ms) from the

Programming Chart

inside the back cover of this manual, then scan Save.

Delay Duration

3-19 Aimer Mode

This feature allows you to turn the aimer on and off. When turning the aimer on,

there are 2 options: Interlaced (the aimer is interlaced with the illumination

LEDs) and Interlace Optimized for Decode (same as Interlaced except the

aimer flashes so that it is not captured in the image).

Note

: If you are having a hard time decoding using Interlaced, use Interlaced

Optimized for Decode.

Off

3-18-1 User-Specified Aimer Delay

3-19 Aimer Mode

Summary of Contents for CM-2D002
















































































































































































































































Search results

Summary of Contents for CM-2D002

Reviews:

Related manuals for CM-2D002

Brands by name

Popular brands

Canmax Technology CM-2D002, User Manual

Search results

Summary of Contents for CM-2D002

Reviews:

Related manuals for CM-2D002

Brands by name

Popular brands