BYD G3 AUTO Owner'S Manual Download Page 151 | Manualshive

Page: 151 / 160

background image

BYD G3 AUTO Owner’s Manual

145

Before Adding Cleanser
Pull out cleanser funnel and hang it
on the brake of engine hood support.

Water can be used as cleanser. But in
cold region where the temperature is
below zero degree, you shall use
cleanser with ant freezing agent. It is
available in BYD service stations and
most auto part stores. For mixing ratio of
water and anti-freezing agent, please
refer to manufacturer’s instructions.
Make sure put back the funnel in place
after filling full the cleanser tank.

Note

Don’t use engine antifreeze or
other substitutes, as they will
damage the vehicle paint.

Replace Bulb

The following figures shows the method
to take off the bulbs. Make sure the
ignition switch and light switches are
turned off when replacing bulbs. Use
bulbs with rated power shown in the
table below:
Parking light and rear parking light
consists of a group of luminous diodes.
When the number of burnt out luminous
diodes affects the car’s compliance with
local laws, please send the car to BYD
service station for replacing bulbs.

Tips

●

Do not replace bulb when it is

hot to avoid burning.

●

The halogen bulb is filled with

pressurized gas, please be
particularly careful. If the bulb
is scratched or falls to ground,
it may explode or crack. Only
hold the bulb on its plastic or
metal part. Do not touch glass
part of the bulb with bare
hands.

When traveling in rain or when the light
shade is wet after washing, the inside of
lamp shade of external light such as
headlight will temporarily fog. As with
fog on the windshield in rainy days, the
fog inside the light shade is due to the
temperature difference between the
inside and the outside of light shade,
and isn’t a trouble. But if there is water
droplet or water pool in the lightshade,
please contact BYD service station.

Bulb W

Type

Headlight (low
beam)

55

H7

Headlight (high
beam)

60

HB3

Front fog light

55

H11

Front turn signal light

21

PY21W

Side turn signal light

1

LED

Rear turn signal light

21

PY21W

Backup light

21

P21W

Rear fog light

21

W21W

High mount brake
light

16

W16W

Name plate light

5

W5W

Door light

5

W5W

Front interior light

5

R5W

Rear interior light

10

C10W

Trunk light

5

W5W

Front parking light

1

LED

Rear parking light

0.5

LED

«
...
149
150
151
152
153
...
»

Summary of Contents for G3 AUTO

































































































































































Reviews:

No comments

Related manuals for G3 AUTO

Brand: RaceChip Pages: 20

Brand: Alpine Pages: 69

Brand: Allen Sports Pages: 2

Brand: Subaru Pages: 34

Brand: Nav TV Pages: 3

Brand: Cadillac Pages: 34

Brand: BMW Pages: 55

Brand: Whispbar Pages: 15

Brand: Xblitz Pages: 30

Brand: GMC Pages: 120

Brand: Prime Tech Pages: 6

Electra 225 1965

Brand: Buick Pages: 914

Brand: Xhorse Pages: 48

Brand: Reese Explore Pages: 9

Brand: Ford Pages: 458

Fleetwood Brougham Sedan 1966

Brand: Cadillac Pages: 56

INDICA eV2 XETA CNG

Brand: TATA Motors Pages: 24

Brand: PAC Pages: 5

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands