manualshive.com logo in svg

Buell Ulysses 2006, Service Manual, Page: 95 / 638

Share
Download
Buell Ulysses 2006 Service Manual Download Page 95

2006 Buell Ulysses: Maintenance

1-27

HOME

DRIVE BELT

1.9

GENERAL

The drive belt tension on a new belt will loosen after approxi-
mately 1000 mi (1600 km). The drive belt tension is automati-
cally adjusted by the idler pulley. Axle alignment is not
adjustable.

Inspect drive belt and idler pulley assembly:

●

At every 5,000 mile (8,000 km) service interval.

INSPECTION

Rear Sprocket

NOTE

If gouges to rear sprocket are large enough to be harmful,
they will leave a pattern on the belt face.

1.

Inspect each tooth of rear sprocket for:

a. 

Major tooth damage.

b. 

Coating chips larger than 1/4 in. (6.35 mm) missing
or removed.

c. 

Gouges caused by hard objects.

2.

Replace rear sprocket if major tooth damage or loss of
coating in an area 1/4 in. (6.35 mm) or larger occurs.

Drive Belt

Refer to 

Table 1-8.

 Inspect drive belt for: 

●

Cuts or unusual wear patterns on both sides of belt.

●

Outside edge bevelling. Some bevelling is common, but it
indicates that sprockets are misaligned.

●

Outside surface for signs of stone puncture. If cracks/
damage exists near edge of belt, replace belt immedi-
ately. Damage to center of belt will require belt replace-
ment eventually, but when cracks extend to edge of belt,
belt failure is imminent.

●

Inside (toothed portion) of belt for exposed tensile cords
(normally covered by facing fabric). This condition will
result in belt failure and indicates worn transmission
sprocket teeth. Replace belt and transmission sprocket.

●

Signs of puncture or cracking at the base of the belt
teeth. Replace belt if either condition exists.

Idler Pulley

See 

Figure 1-31.

 Inspect idler pulley for signs of uneven wear.

Excessive lateral side play of 0.020 in. (0.5 mm) or roughness
indicates worn bearings. Replace idler pulley as an assembly.
See 

6.6 DRIVE BELT SYSTEM

.

CLEANING

Keep dirt, grease, oil, and debris off the belt, idler pulley and
sprockets. Clean the drive belt with a mild soap and water
spray solution as required. Dry thoroughly. Do not immerse
belt in solution. Do not direct pressurized water on belt.

Figure 1-31. Checking Lateral Side Play on Idler Pulley 

with a Dial Indicator

10124

Summary of Contents for Ulysses 2006































































































































































































































































































































































































































































































































































































































































Reviews:

No comments