Buell Ulysses 2006, Service Manual, Page: 126 / 638

2-2 2006 Buell Ulysses: Chassis
HOME
TORQUE VALUES
ITEM TORQUE NOTES
Axle (front) 39-41 ft-lbs 53-56 Nm ANTI-SEIZE, Left handed thread, page 2-17
Axle (rear)
48-52 ft-lbs 65.1-70.5 ANTI-SEIZE, Tighten to 23-27 ft-lbs (31.2-36.6 Nm)
then back off 2 turns and final tighten, page 2-21
Axle pinch fastener, rear 40-45 ft-lbs 54-61 Nm page 2-21
Axle pinch fasteners, front 20-22 ft-lbs 27-30 Nm page 2-17
Battery terminal fasteners 72-96 in-lbs 8-11 Nm page 3-68
Brake hand lever housing fasteners 80-90 in-lbs 9-10 Nm page 2-30
Brake lamp switch fastener, front 7-10 in-lbs 0.8-1.0 Nm page 2-30
Brake line bracket fasteners 48-60 in-lbs 5-7 Nm page 2-42
Brake line p-clamp fastener, front 36-60 in-lbs 4-7 Nm page 2-33
Brake line P-clamp on inside of
lighting module 36-60 in-lbs 4-7 Nm page 2-33
Brake pedal fastener 22-24 ft-lbs 30-33 Nm LOCTITE 272, page 2-27
Brake pin hanger set, front 11-14 ft-lbs 15-19 Nm page 2-35
Brake pin hanger set, rear 11-14 ft-lbs 15-20 Nm page 2-44
Brake pin plug, rear 24 in-lbs 2.7 Nm page 2-44
Caliper banjo bolt, front 16-20 ft-lbs 22-27 Nm metric, page 2-33
Caliper banjo bolt, rear 16-20 ft-lbs 22-27 Nm page 2-42
Caliper bleeder valves 36-60 in-lbs 4-7 Nm metric, page 2-28
Caliper carrier, rear 24-26 ft-lbs 32-35 Nm page 2-21
Caliper fasteners, front 15-19 ft-lbs 20-26 Nm page 2-35
Caliper mounting fasteners, front 35-37 ft-lbs 47-50 Nm page 2-35
Caliper mounting large fastener,
rear (metric) 18-21 ft-lbs 24-28 Nm page 2-45
Caliper mounting small fastener,
rear (metric) 14-18 ft-lbs 19-24 Nm page 2-45
Chin fairing fasteners 36-48 in-lbs 4-5 Nm page 3-92
Clutch cable p-clamp 25-27 ft-lbs 33.9-36.6 Nm page 3-74
Clutch cable wire form retainer 84-92 in-lbs 9.5-10.4 Nm page 3-64
Clutch cable wire form 84-92 in-lbs 9.5-10.4 Nm page 3-74
Clutch inspection cover fasteners 84-108 in-lbs 9.5-12.2 Nm Tighten in a crosswise pattern, page 3-74
Deflector fasteners 24-36 in-lbs 2.7-4.1 Nm page 3-70
Deflector jam nuts 39-48 in-lbs 4.4-5.4 Nm page 3-70
Deflector pivot shaft riser 43-49 in-lbs 4.8-5.5 Nm page 3-70
ECM fasteners 36-60 in-lbs 4.0-6.8 Nm page 3-101
Engine shroud air scoop 12-36 in-lbs 1-4 Nm page 3-94
Exhaust header mounting nut 72-96 in-lbs 8-11 Nm page 3-85
Footpeg mount 132-144 in-lbs 15-16 Nm LOCTITE 272, page 3-88
Fork cap to damper rod 22-29 ft-lbs 30-39.3 Nm page 2-52
Fork cap to fork tube 132-144 in-lbs 14.9-16.2 Nm page 2-52
Fork center bolt 22-30 ft-lbs 30-40 Nm page 2-51
Fork clamp, lower 20-22 ft-lbs 27-30 Nm LOCTITE 272 (red), page 2-53
Fork clamp, upper 23-25 ft-lbs 31-34 Nm LOCTITE 272, page 2-53
Fork damper locknut 22-30 ft-lbs 30-40 Nm page 2-51