manualshive.com logo in svg

Buell Ulysses 2006, Service Manual, Page: 577 / 638

Share
Download
Buell Ulysses 2006 Service Manual Download Page 577

 

2006 Buell Ulysses: Electrical

7-23

 

HOME

 

INSTALLATION

 

NOTE

 

●

 

Never reuse front muffler strap. Always replace front muf-
fler strap with a new strap when removed from system.

 

●

 

It is necessary to install interactive exhaust cable to muf-
fler with muffler only partially installed.

 

1.

Install muffler. See 

2.32 EXHAUST SYSTEM

.

2.

Install interactive cable onto vehicle.

a. 

Slip end of hose over upper end of cable and attach
with tape.

b. 

See 

Figure 7-22.

  Gently pull cable assembly up

through the wire harness strap and guide at the left
rear corner of the frame/fuel tank assembly. See

1.16 INTERACTIVE EXHAUST CABLE

.

3.

Install actuator. Tighten fasteners to 36-40 in-lbs (4.1-4.5
Nm).

4.

Attach interactive exhaust cable to cable wheel on actua-
tor.

5.

Connect interactive exhaust harness to actuator [161B].

6.

Route fuel vent line and install.

7.

Attach interactive exhaust cable to bracket and cable
wheel on actuator and adjust. See 

1.16 INTERACTIVE

EXHAUST CABLE.

8.

Install intake cover. See 

2.39 INTAKE COVER

.

1

WARNING

1

WARNING

 

Connect positive (+) battery cable first. If positive (+)
cable should contact ground with negative (-) cable con-
nected, the resulting sparks can cause a battery explo-
sion, which could result in death or serious injury.
(00068a)

 

9.

Install negative battery cable to battery terminal. Tighten
fastener to 72-96 

 

in-lbs

 

 (8-11 Nm).

1

WARNING

1

WARNING

 

After installing seat, pull upward on front of seat to be
sure it is in locked position. While riding, a loose seat can
shift causing loss of control, which could result in death
or serious injury. (00070a)

 

10. Install seat. See 

2.45 SEAT.

 

Figure 7-22.  Interactive Exhaust Cable Behind 

Wire Harness Strap and Guide

Summary of Contents for Ulysses 2006































































































































































































































































































































































































































































































































































































































































Reviews:

No comments