MY HOME cOntROL
technical
GUiDe
69
configurAtion
rear view
room number
light point number
not used
local address
of the IR receiver
This mode enables you to associate a single control with any key of the
remote control. It is possible to associate up to 16 controls with a remote
control using only one receiver (using the 16 channel remote control -
4482/16). Configure the receiver with address A=0 and PL=1-9 which cannot
be used by actuators.
Controls that the receiver can “learn”:
- ON/OFF actuator (ON/OFF cyclical functioning for short pressure and
adjustment for long pressure)
- Timed ON
- Flashing
- UP-DOWN rolling shutter (up-down until end of stroke)
- Lock/Unlock actuator
- ON/OFF, lights – auxiliary (cyclic ON/OFF functioning)
- UP-DOWN rolling shutter auxiliary (up-down until end of stroke)
- Video door entry system (door lock and Staircase lights)
- Sound system (see “Sound system” Technical guide)
to associate a different control with each of the remote control channels,
follow the procedure below:
1) press the pin pushbutton for 3 seconds: the LED will turn on steadily;
2) within 20 seconds press the key of the channel you want to program
on the remote control: the LED will begin to flash, hence indicating the
activation of the programming mode;
3) set up the control you want to associate with the remote control key using
the controls and/or corresponding actuator: the LED will turn on steadily;
4) you can now repeat 2) and 3) for all keys, even for a key that has already
been associated, in case you want to change it;
5) press the pin key to exit the programming mode: the LED will turn off.
to cancel the programming of one of the remote control channels, follow
the procedure below:
1) press the pin pushbutton for at least 8 seconds: the LED will turn on
steadily after 3 seconds; it will turn off after another 5 seconds; release
the key within 4 seconds: the LED will turn on steadily;
2) within 20 seconds press the key of the channel you want to cancel on the
remote control: The LED will start flashing quickly for about 4 seconds,
thus confirming the cancellation;
3) from now on, the cancelled key will no longer activate any control until it
is re-programmed.
to cancel the programming of all remote control channels
simultaneously,
press the pin pushbutton for about 12 seconds: the LED will turn on steadily
after 3 seconds; it will turn off after another 5 seconds; after another 4
seconds, it will start flashing quickly for about 4 seconds, thus confirming the
cancellation of all programming conditions.
NOTE: with the two-way switch in the “closed padlock” position
programming and cancelling the device are forbidden.
This mode can be used only if the system includes a scenario module item
F420. It lets you create, cancel or modify the scenarios contained in the
scenario module, thus activating them with the remote control. The procedure
lets you store up to 16 scenarios using all 16 channels of the 16-channel
remote control. The following table shows the correspondence between the
number of the scenario stored in the scenario module and the remote control
channels:
Number of
16-channel remote
7-channel remote
scenario module
control 4482/16
control 4482/7
Scenario 1
Ch1
Ch1
Scenario 2
Ch2
Ch2
Scenario 3
Ch3
Ch3
Scenario 4
Ch4
Ch4
Scenario 5
Ch5
Ch5
Scenario 6
Ch6
Ch6
Scenario 7
Ch7
Ch7
Scenario 8
Ch8
Scenario 9
Ch9
Scenario 10
Ch10
Scenario 11
Ch11
Scenario 12
Ch12
Scenario 13
Ch13
Scenario 14
Ch14
Scenario 15
Ch15
Scenario 16
Ch16
The scenario module must be configured with self-learning function enabled (it
is necessary to press the self-learning key so that the associated LED is green
– if it is red, the function is not enabled) and the two-way switch on the back
side of the IR receiver must be in the “padlock open” position.
To program a scenario, follow the procedure below:
1) press the pin pushbutton for 3 seconds: the LED will turn on steadily;
release the key;
2) within 20 seconds press the key of the scenario you want to program
on the remote control: the LED will begin to flash, hence indicating the
activation of the programming mode;
3) set the scenario using the controls and/or actuators;
4) press the pin key to exit the programming mode: the LED will turn off;
5) repeat 1) and 4) for all the scenarios you want to program.
To cancel a scenario, follow the procedure below:
1) press the pin pushbutton for 8 seconds: the LED will turn on steadily after
3 seconds; it will turn off again after another 5 seconds; release the key
within 4 seconds: the LED will turn on steadily;
2) within 20 seconds press the key of the scenario you want to cancel on the
remote control: when the scenario module confirms the cancellation, the
LED will start flashing quickly for about 2 seconds and then it will turn off;
3) repeat 1) and 2) for all the scenarios you want to cancel.
NOTE: configure the device with address A=0 and PL=1-9 which cannot be
used by actuators.
mode “B” (self-leArning - remote) m=0
mode “c” (scenArio module control item f420) m=6
