Bticino D45, Technical Manual

Page: 20 / 156

SONORA - CARATTERISTICHE GENERALI
18
VIDEO DOOR ENTRY SYSTEM - GENERAL FEATURES
D45
hanDset monitoring other Devices
Small EP monitoring
Press the monitor pushbutton twice while in standby .
The display will show the picture recorded by Small EP
camera . Pick up the receiver to start the conversation, the
call light flashed slowly; Put down the receiver to end the
conversation . The device will go back to standby status .
Note: Small EP monitoring function must be enabled during installation settings.
Monitoring riser Entrance Panels
Press the monitor pushbutton while in standby . The display
will show the picture recorded by riser EP camera . At
the monitor status, if there are several riser EPs, press the
monitor pushbutton again to view the next riser EP . Using
this procedure it will be possible to view all EPs . Pick up
the receiver to start the conversation, the call light flashes
slowly; Put down the receiver to end the conversation . The
device will go back to standby status .
calling other Devices
Calling main Switchboard
While in standby, press the Switchboard pushbutton to call
the Switchboard and wait for the Switchboard to answer
the call . Put down the receiver to end the conversation . The
device will go back to standby status .
Handset call other Switchboard
While in stand by, digit Switchboard press
Switchboard call key or press Switchboard key directly
to call main Switchboard . (Such as IU 102 call the 4th .
Switchboard): On handset keyboard input 4 key then press
Switchboard key within 10 seconds .
Note: for handsets you must pick up the handset to start conversation.
Calling internal handsets
While in standby status, press and hold down the monitor
pushbutton until an extended beep is heard . Release
the pushbutton to initiate the internal call . Put down the
receiver to end the conversation . The device will go back to
standby status .
Call other handsets in the same riser
On handset input IU Intercom key – if only
intercom key is pressed you call the same IU number . (Such
as IU102 call IU104) : on handset keyboard 102 digit 104 +
intercom key then long press monitor key and release .
Video door entry functions
instructions
1 . For all pushbuttons, the operation is only performed
after the pushbutton is released . When holding the
pushbutton down is required, the pushbutton should
only be released after an extended beep is heard .
2 . Operation indication: a short or a long beep indicates
successful operation; 3 short beeps or busy tone indicate
unsuccessful operation or system busy .
3 . If an apartment has several handsets installed, when a
call arrives, only the display of the master handset will
come on . The display of the other slave handsets will not
come on, unless the call is answered by them . However,
they will ring together with the master handset .
receiving calls
Receiving calls from the EP:
When handset rings, and the call light flashes quickly, it
means a call is coming . The display will show the picture
recorded by EP camera; press the answer pushbutton or pick
up the handset to accept the calls . While the system is busy
with the conversation the call light will flash slowly . Press
the answer pushbutton or put down the receiver to end the
call, than the device will come back to standby status . Unless
otherwise specified, “EP” in this manual means (Backbone/
Main EP) or (riser / secondary EP)
Note: for Handsfree handsets, both answering and terminating a call are done by
pressing the answer pushbutton; for Standard handsets, pick up the receiver to
answer the call and put down the receiver to terminate the call
Receiving calls from Small EPs:
The handset will ring . The procedures are the same as
explained in “Receiving calls from the EP” .
Receiving calls from the Switchboard:
When handset rings, and the call light flashes quickly, it
means a call is coming . The display will show the picture
recorded by Switchboard camera if the Switchboard is
fitted with one ; press the answer pushbutton or pick up the
handset to accept the calls . While the system is busy with
the conversation the call light will flash slowly . Press the
answer pushbutton or put down the receiver to end the call,
and the device will come back to standby status .
Receiving internal calls:
The handset will ring . The procedures are the same as
explained in “Receiving calls from the EP”, but without video .
Indoor handset functions overview