Brother GTX pro Instruction Manual Download Page 58

Page: 58 / 356

Installation and preparation

(17)

Click [Finish]. This exits the setting for the PC.

<TIPS>



If the PC cannot recognize the Printer, a correct static IP address might not be assigned. Consult your administrator.

(18)

Adjust the carriage speed. Then adjust the printer using "GTX pro Maintenance".

Menu name

Things to prepare

See the operating procedure with

GTX pro Maintenance

1 [CR

Speed

Adjustment]

―

"7-4-1. CR (Carriage) speed
adjustment >>P.216"

[Initial settings after head
replacement]

―

"7-4-2. Initial settings after head
replacement >>P.217"

3 [Firing

Adjustment]

Black paper or transparent sheet
(such as OHP sheet)
White paper

"7-4-3. Firing adjustment >>P.218"

[Platen-Rolling Adjustment]

White paper

"7-4-4. Platen-rolling adjustment
>>P.219"

5 [White/Color

Alignment]

Black paper or pretreated black or
dark color T-shirt

"7-4-5. White/color alignment
>>P.220"

[Setting of the time displayed
on the nozzle check pattern]

―

"7-4-6. Setting of the time displayed
on the nozzle check pattern >>P.221"

Summary of Contents for GTX pro





































































































































































































































































































































































Search results

Summary of Contents for GTX pro

Reviews:

Brother GTX pro, Instruction Manual, Page: 58 / 356

Search results

Summary of Contents for GTX pro

Reviews: