Home
/
Brother
/
GTX pro
/
Instruction Manual

Brother GTX pro, Instruction Manual, Page: 124 / 356

Share

Page: 124 / 356

Brother GTX pro Instruction Manual Download Page 124

124

Basic printing procedures

6-3-2. Dilution of pretreatment

Be sure to use the pretreatment after diluting it with pure water.
<CAUTION>



Be sure to wear a pair of plastic gloves and protective glasses during the work operation.



For information on handling of the pretreatment, see the Material Safety Data Sheet issued by us.

http://sds.brother.co.jp/sdsapp/index.html

Dilution ratio

Use within the ratio range of x3 (Pretreatment:Pure water=1:2) (Volume ratio).

Dilution method

<TIPS>



The figure below is based on the pretreatment (20 kg (44 lb)). When using the pretreatment (5 kg (11 lb)), remove the cap and
pour the agent into the container, and dilute it with pure water, referring to step (4) and the subsequent steps. Dilution ratio is the
same.

(1)

Unpack the pretreatment container from the shipping carton by cutting off the perforated paper along the perforated

tear-off line to open the carton.

X0079

(2)

Remove the cap, and place the cap in position.

X0080

Pretreatment

Faucet

Cap

Pretreatment

«
...
122
123
124
125
126
...
»

Summary of Contents for GTX pro





































































































































































































































































































































































Reviews:

No comments