Home
/
Brother
/
GTX pro
/
Instruction Manual

Brother GTX pro, Instruction Manual, Page: 286 / 356

Share

Page: 286 / 356

Brother GTX pro Instruction Manual Download Page 286

286

Troubleshooting

< Old capping pouch>

<CAUTION>



Avoid touching the portion (a) of cartridge. Otherwise, you may cut your hand.

<NOTE>



Close the lid while holding the slack of the capping pouch by hand.



After closing the lid, confirm that the capping pouch has been taken up to the end. When the latch of the cartridge side is
raised, the winding is complete.

X0041

(a)

X0201

(8)

Close the lid, and put the capping cartridge in position inside the printer.

(9)

Repeat the same process to replace the other white ink cartridge with the capping pouch.

(10)

Follow the on-screen message and turn off the power.

<IMPORTANT>



Please complete the task within 15 minutes, in order to prevent the print heads from drying up.

(11)

Open the front cover.

X0331

(12)

Remove the upper case of a new print head.

Front cover

Place the pouch in a straight alignment with the cartridge

Align lines with
each other

Latch

Cartridge

«
...
284
285
286
287
288
...
»

Summary of Contents for GTX pro





































































































































































































































































































































































Reviews:

No comments