manualshive.com logo in svg

Brother GTX pro, Instruction Manual, Page: 179 / 356

Share
Download
Brother GTX pro Instruction Manual Download Page 179

 

179 

Precautions to keep good printing quality/use printer over the long term

(4) 

Wipe the resin part between the print head's nozzle surface and nozzle guard. 
<IMPORTANT> 

 

Be sure not to touch the red-frame zone of the nozzle surface. 

 

For cleaning, be sure not to use any tool other than clean stick R. 

X0237

 

 
Cleaning conditions 

Pre-cleaning state 

Post-cleaning state 

 

 

 
<IMPORTANT> 

 

Be sure to use the clean stick R separately for white ink and color ink. 

<TIPS> 

 

There may remain white ink in the black resin part, but it doesn't matter if the severity is small as shown in the photo. Wipe away 
the white ink spreading out of the nozzle guard and nozzle surface. 

Clean this part 

Cleaning location 
Between the nozzle surface and nozzle guard

Cleaning location 
Between the nozzle surface and nozzle guard 

Nozzle surface

Nozzle guard 

X0238

Cleaning location 
Between the nozzle surface and nozzle guard

Summary of Contents for GTX pro





































































































































































































































































































































































Reviews:

No comments