manualshive.com logo in svg

Brother GTX pro, Instruction Manual, Page: 26 / 356

Share
Download
Brother GTX pro Instruction Manual Download Page 26

 

26 

Name and function of each component

2-3.  Left side view/Rear side view 

X0308

4

3

1

2

2

1

6

5

 

No. 

Name 

Function 

1 Exhaust 

opening 

This is the exhaust outlet for fan exhaust air. For proper use, keep this opening 
apart from the nearest wall by 7.9 in. (20 cm) or more. 

2 

Fan filter 

It absorbs ink mist which is generated inside the printer on its surface. 

3 

Waste ink tube 

This tube is used to direct the flow of waste ink down into the waste ink tank. 

4 

Waste ink tank 

This tank collects waste ink. 

5 

Cleaning liquid tank 

It is the tank that reserves the cleaning solution used for maintenance. 

6 

Rear cover 

It protects the platen's working range. 

 

Summary of Contents for GTX pro





































































































































































































































































































































































Reviews:

No comments