Brother GTX pro Instruction Manual Download Page 223

Page: 223 / 356

223

Precautions to keep good printing quality/use printer over the long term

7-4-7. Set the scheduled time for white ink circulation

White ink circulation can be performed at a specified time. If not set, white ink circulation will be performed automatically
every six hours.

(1)

Make sure that a connection of USB 2.0 cable or LAN cable is made between the printer and your PC.

(2)

On the PC, from [All Programs] in the Start menu, select the "GTX pro Maintenance" of "Brother GTX pro Tools".

(3)

After the window shown below appears, select [Set the scheduled time for white ink circulation] and click [Next].

(4)

After the window shown below appears, select [Set the scheduled time for white ink circulation.] and click [Next].

Summary of Contents for GTX pro





































































































































































































































































































































































Search results

Summary of Contents for GTX pro

Reviews:

Brother GTX pro, Instruction Manual, Page: 223 / 356

Search results

Summary of Contents for GTX pro

Reviews: