Home
/
Brother
/
GTX pro
/
Instruction Manual

Brother GTX pro, Instruction Manual, Page: 264 / 356

Share

Page: 264 / 356

Brother GTX pro Instruction Manual Download Page 264

264

Troubleshooting

(7)

Put the maintenance solution pouch in its correct position.
<CAUTION>



Avoid touching the portion (a) of cartridge. Otherwise, you may cut your hand.

X0041

(a)

(8)

Close the lid, and put the maintenance solution cartridge in position inside the printer.

(9)

Repeat the same process to replace the other white ink cartridge with the maintenance solution pouch.

(10)

On the operation panel, press

.

Then, the white head cleaning will be performed.

<TIPS>



White head cleaning will take approximately 25 minutes. Perform the "Install White Ink After Cleaning" operation by
following the on-screen instructions.

Place the pouch in a straight alignment with the cartridge

Align lines with
each other

«
...
262
263
264
265
266
...
»

Summary of Contents for GTX pro





































































































































































































































































































































































Reviews:

No comments