manualshive.com logo in svg

Brother GTX pro, Instruction Manual, Page: 155 / 356

Share
Download
Brother GTX pro Instruction Manual Download Page 155

 

155 

Basic printing procedures

6-6-2.    Sending print data from applications 

CorelDRAW 

(1) 

In the menu bar, select [File] > [Print]. 

(2) 

Open the [Color] tab, and make the following settings: 

  Place a checkmark in the [Document color] checkbox. 

  [Color conversions]: "Brother GTX pro" or "Brother GTX pro FileOutput" 

  [Color profile]: [sRGB IEC61966-2.1] 

  [Rendering intent]: [Relative colorimetric] 

 

(3) 

Open [General] tab and select "Brother GTX pro" from [Printer]. 
<TIPS> 

 

If the specified [Printer] is set to "Brother GTX pro", the print data will be sent to the printer.   
If the specified [Printer] is set to "Brother GTX pro FileOutput", the print data will be saved as an ARXP file. 

(4) 

On [Preferences], set up the printer driver and send the print data by clicking [OK] in the [Print] dialog box. 
<TIPS> 

 

Setting the printer driver 

☞

"5-4. Set up the printer driver >>P.89" 

 

Clicking on [OK] will not start the print operation of the printer itself. The print button of the printer should be pressed to start 
the printing operation. 

Summary of Contents for GTX pro





































































































































































































































































































































































Reviews:

No comments