Brother GTX pro Instruction Manual Download Page 288

Page: 288 / 356

288

Troubleshooting

(15)

Remove the core claw using the supplied screwdriver.

<TIPS>



Hold the core center by hand to make it easy to insert the screwdriver into the claw.

X0408

(16)

Remove the resin cover which is placed on the top of the carriage board and remove the flat cable.

X0409

(17)

Unlock the print head, and remove the print head.



When removing the print head, be careful not to drip the ink on the carriage plate. If the ink is dripping, wipe off the dripping
ink.

②

①

X0410

Lock

Print head

Resin cover

Flat cable

Driver

Core

Latch

Summary of Contents for GTX pro





































































































































































































































































































































































Search results

Summary of Contents for GTX pro

Reviews:

Brother GTX pro, Instruction Manual, Page: 288 / 356

Search results

Summary of Contents for GTX pro

Reviews: