Home
/
Brother
/
GTX pro
/
Instruction Manual

Brother GTX pro, Instruction Manual, Page: 202 / 356

Share

Page: 202 / 356

Brother GTX pro Instruction Manual Download Page 202

202

Precautions to keep good printing quality/use printer over the long term

(4)

By pressing

, select the [All Colors], [All Whites], or [All Print Heads], and press

.

<TIPS>



Under the condition that the nozzle which has been confirmed not ejecting ink-jet droplets, determine the color for which the
head cleaning should be performed.

☞

"7-2-1. Print out of the nozzle check pattern (checking on the print heads) >>P.199"

(5)

Then, the head cleaning will be performed for the specified print heads.
<TIPS>



The cleaning operation cannot be canceled halfway.



After the procedures are completed, the current screen will go back to the standby mode screen.

«
...
200
201
202
203
204
...
»

Summary of Contents for GTX pro





































































































































































































































































































































































Reviews:

No comments