Brother GTX pro Instruction Manual Download Page 129

Page: 129 / 356

129

Basic printing procedures

(4)

Attach the pretreatment roller to the handle (handgrip of roller).

<TIPS>



Use a commercially available handle provided with a roller that fits the pretreatment roller's inside diameter of 0.8 in. (21
mm).

X0089

(5)

Pour the diluted pretreatment into the tray, and dip the pretreatment roller in the agent so that it will be dampened

with the agent.

X0090

(6)

Rub the pretreatment roller well against the scrub board of the tray and squeeze a redundant agent out of it.

X0091

Handle (handgrip of roller)

Pretreatment roller

Pretreatment

Tray

Pretreatment roller

Tray

0.8 in. (21 mm)

Summary of Contents for GTX pro





































































































































































































































































































































































Search results

Summary of Contents for GTX pro

Reviews:

Brother GTX pro, Instruction Manual, Page: 129 / 356

Search results

Summary of Contents for GTX pro

Reviews: