Brother GTX pro Instruction Manual Download Page 154

Page: 154 / 356

154

Basic printing procedures

(4)

For the print data that requires multiple cycles of platen reciprocate movement, print data of each layer can be

verified separately by selecting the desired layer to be displayed. From the [Present Layer], select a layer that you

want to bring into the view.

<TIPS>



In the layer that is shown as [Total], the preview window of the final print result is displayed.



When the [White Data] checkbox is marked, the preview window for white ink only will be displayed.

(5)

Check the printing conditions and preview window, and click on [Send to Printer].

Then, the ARXP file is sent to the printer.
<TIPS>



Make sure that a connection of USB 2.0 cable or LAN cable is made between your PC and the printer.



In the event that two or more GTX pro printer drivers have been installed on your PC, select one of them and click [OK].

Summary of Contents for GTX pro





































































































































































































































































































































































Search results

Summary of Contents for GTX pro

Reviews:

Brother GTX pro, Instruction Manual, Page: 154 / 356

Search results

Summary of Contents for GTX pro

Reviews: