Brother DCP-9045CDN Service Manual Download Page 6

Page: 6 / 491

Confidential

CHAPTER 3 DISASSEMBLY AND ASSEMBLY ..................................... 3-1

8.1 Paper Tray ........................................................................................................................3-35

8.2 DX Feed ASSY .................................................................................................................3-37

8.3 MP Cover ASSY/ MP Paper Guide ASSY........................................................................3-37

8.4 MP Lift Arm 2/ MP Roller Holder ASSY............................................................................3-40

8.5 Fuser Unit/ Toner Filter Frame ASSY...............................................................................3-43

8.6 Back Cover Upper ............................................................................................................3-45

8.7 Paper Eject ASSY DX.......................................................................................................3-46

8.8 Back Cover ASSY.............................................................................................................3-48

8.9 Paper Guide/ HV TR Top Cover.......................................................................................3-49

8.10 Transfer HVPS PCB Unit................................................................................................3-50

8.11 Registration-mark Sensor PCB ASSY 1, 2/ Density Sensor/ Registration Relay PCB

ASSY/ Transfer HVPS PCB ASSY.................................................................................3-51

8.12 Side Cover L ASSY ........................................................................................................3-57

8.13 Side Plate LB ..................................................................................................................3-58

8.14 Drum Unit Fan (OPC) .....................................................................................................3-59

8.15 Side Cover R ASSY........................................................................................................3-60

8.16 Paper Stopper.................................................................................................................3-61

8.17 Driver PCB ASSY ...........................................................................................................3-62

8.18 Pull arm L, R/ Hinge Protection Cover ASSY.................................................................3-64

8.19 ADF Unit .........................................................................................................................3-68

8.20 Panel Unit .....................................................................................................................3-102

8.21 Document Scanner Unit ...............................................................................................3-107

8.22 NCU PCB ASSY (MFC-9840CDW only) ......................................................................3-117

8.23 Battery ASSY................................................................................................................3-120

8.24 Joint Cover ASSY .........................................................................................................3-121

8.25 Speaker ASSY..............................................................................................................3-127

8.26 Roller Holder ASSY ......................................................................................................3-129

8.27 Paper Feed Frame Unit/ T1 PE/Edge Sensor PCB ASSY ...........................................3-130

8.28 Belt Cleaner Release Sensor PCB ASSY ....................................................................3-138

8.29 THM/HUM Sensor Holder ASSY ..................................................................................3-139

8.30 Release Rack ...............................................................................................................3-141

Summary of Contents for DCP-9045CDN












































































































































































































































































































































































































































































































Search results

Summary of Contents for DCP-9045CDN

Reviews:

Brands by name

Popular brands

Brother DCP-9045CDN, Service Manual

Search results

Summary of Contents for DCP-9045CDN

Reviews:

Brands by name

Popular brands