Brother DCP-9045CDN Service Manual Download Page 371

Page: 371 / 491

Confidential

5-11

1.4.7 Operational Check of LCD (Function code 12)

<Function>

This function allows you to check whether the LCD on the control panel works normally.

<Operating Procedure>

(1) Press

the

and

buttons in this order in the initial stage of the maintenance mode. The

LCD shows.

(2) Press

the

Black Start

button. Each time you press the

Black Start

button, the LCD and

Status LED cycle through the displays shown below.

(3) Press

the

Stop/Exit

button in any process of the above display cycle. The machine beeps

for one second and returns to the initial stage of the maintenance mode.

< LCD >

< Status LED >

Status

Fig. 5-4

Backlight ON

Backlight OFF

Yellow

Red

Green

Summary of Contents for DCP-9045CDN












































































































































































































































































































































































































































































































Search results

Summary of Contents for DCP-9045CDN

Reviews:

Related manuals for DCP-9045CDN

Brands by name

Popular brands

Brother DCP-9045CDN, Service Manual

Search results

Summary of Contents for DCP-9045CDN

Reviews:

Related manuals for DCP-9045CDN

Brands by name

Popular brands