Brother DCP-9045CDN Service Manual Download Page 178

Page: 178 / 491

Confidential

3-45

(4) Remove the Toner filter frame ASSY from the Paper eject ASSY DX.

Fig. 3-20

8.6 Back Cover Upper

(1) Remove the two cup S M3x8 Taptite screws, and then remove the Back cover upper.

Note:

Be careful not to break the plastic. As this can be difficult to remove and reassemble.

Fig. 3-21

Back cover upper

Taptite, cup S M3x8

Toner filter frame ASSY

Paper eject ASSY DX

Summary of Contents for DCP-9045CDN












































































































































































































































































































































































































































































































Search results

Summary of Contents for DCP-9045CDN

Reviews:

Brands by name

Popular brands

Brother DCP-9045CDN, Service Manual

Search results

Summary of Contents for DCP-9045CDN

Reviews:

Brands by name

Popular brands