Brother DCP-9045CDN Service Manual Download Page 94

Page: 94 / 491

Confidential

1-75

Pickup function of paper tray does not work.

Step

Cause

Remedy

Link lever not operating
smoothly or catching.

Make sure correct movemet of the link lever.

Pickup roller holder ASSY not
operating smoothly or
catching.

Make sure correct movement of the pickup roller
holder ASSY.

Link lever damaged

Replace the link lever.

Roller holder ASSY failure

Replace the roller holder ASSY.

Paper feed/belt cleaner motor
failure

Replace the paper feed/belt cleaner motor.

The new toner is not detected.

Step

Cause

Remedy

New toner actuator not
operating smoothly or
catching.

Make sure correct movement of the new toner
actuator of the appropriate color.

New toner actuator damaged

Replace the drum unit.

Main PCB failure

Replace the main PCB ASSY.

Toner sensor PCB (TE/NEW)
failure

Replace the toner sensor PCB ASSY (TE/NEW) of
the appropriate color.

Summary of Contents for DCP-9045CDN












































































































































































































































































































































































































































































































Search results

Summary of Contents for DCP-9045CDN

Reviews:

Brands by name

Popular brands

Brother DCP-9045CDN, Service Manual

Search results

Summary of Contents for DCP-9045CDN

Reviews:

Brands by name

Popular brands