manualshive.com logo in svg

Brother DCP-9045CDN, Service Manual

Share
Download
Brother DCP-9045CDN Service Manual Download Page 381

Confidential 

5-21

1.4.14  Received Data Transfer Function (Function code 53) (MFC-9840CDW only) 

<Function> 

This function transfers received FAX data to another machine. It is useful when the machine 
cannot print received data due to the printing mechanism being defective.  It also transfers the 
maintenance information of the machine via FAX. 

Note: 

The number of files that can be transferred at a time is 99. To transfer 100 files or more, carry 
out the following procedure more than one time. 

TIP: 

If there are both color and monochrome data in a file to be transferred, the monochrome data 
will be transferred first. If the receiver machine does not support the color function, the sender 
machine cannot transfer color data, resulting in an error. 

<Operating Procedure> 

(1) Press 

the 

5

 and 

3

 buttons in this order in the initial stage of the maintenance mode. 

The “FAX TRANSFER” appears on the LCD. 

(2)  To check the number of received files, press the 

1

 button. 

The “1.NO. OF JOBS” appears on the LCD. 
Press the 

OK

 button, and the number of received files appears, just as “NO. OF. JOBS: 

10.” 

(3)  To transfer the activity report only, press the 

2

 button. 

The “2.ACTIVITY” appears. 
To transfer received files (together with the activity report), press the 

3

 button. 

The “3.DOCUMENTS” appears. Note that if there is no received file, the “NO 
DOCUMENTS” appears. 

(4)  To transfer the communication list for the latest communication, press the 

4

 button. 

The “4.COM.LIST (NEW)” appears. 
To transfer the communication list for last three errors, press the 

5

 button. 

The “5.COM.LIST (ERR3)” appears. 

(5)  To transfer the maintenance information (the list in Function code 77), press the 

6

 button. 

The "6.MNT77 LIST" appears on the LED. 

(6)  With the “2.ACTIVITY,” “3.DOCUMENTS,” “4.COM.LIST (NEW),” “5.COM.LIST (ERR3)” 

or “6.MNT77 LIST” being displayed, press the 

OK

 button. 

The “ENTER NO. & SET” appears. 

(7)  Enter the telephone number of the receiver machine and press the 

OK

 button again. 

Note: 

Be sure to type the telephone number with the numerical buttons. No one-touch dialing is 
allowed in this procedure. 
The machine displays the “ACCEPTED” for approx. two seconds and starts dialing to transfer 
data. 
No station ID will be attached. A cover page and end page as shown on the next page will be 
automatically attached, instead. 

Summary of Contents for DCP-9045CDN












































































































































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands