Brother DCP-9045CDN Service Manual Download Page 65

Page: 65 / 491

Confidential

1-46

One color is light

User Check

- Check the machine’s environment. High temperature and high humidity conditions can cause

this problem.

- Replace the toner cartridge or drum unit with a new one.
- Implement calibration from the control panel.

Step

Cause

Check

Result

Remedy

Dirt on exposure
drum electrode

Are the electrodes of the
drum unit and the
appropriate color and
machine body dirty?

Yes

Clean both electrodes.

Dirt on belt unit
electrode

Are the electrodes of the
belt unit and the
appropriate color and
machine body dirty?

Yes

Clean both electrodes.

Dirt on scanner
windows

Is the scanner windows of
the appropriate color
dirty?

Yes

Wipe the dirt off with a
soft, clean, lint free cloth.

After replacing the toner
cartridge of the
appropriate color with a
new one, does the same
problem occur even after
printing several pages?

Replace the toner
cartridge of the
appropriate color.

Toner sensor
failure

Does the machine start
printing even after
removing the toner
cartridge of the
appropriate color from the
drum unit?

Yes

- Clean the toner sensor

of the appropriate color.

- Check the harness

connection of the toner
sensor PCB ASSY
(TE/NEW) of the
appropriate color.

- Replace the toner

sensor PCB ASSY
(TE/NEW) of the
appropriate color.

6 Transfer

HVPS

PCB failure

Is the problem solved after
replacing the transfer
HVPS PCB ASSY?

Yes

Replace the transfer
HVPS PCB ASSY.

7 Charge

HVPS

PCB failure

Is the problem solved after
replacing the charge
HVPS PCB ASSY?

Yes

Replace the charge
HVPS PCB ASSY.

8 Engine

PCB

failure

Is the problem solved after
replacing the engine PCB
ASSY?

Yes

Replace the engine PCB
ASSY.

Summary of Contents for DCP-9045CDN












































































































































































































































































































































































































































































































Search results

Summary of Contents for DCP-9045CDN

Reviews:

Brands by name

Popular brands

Brother DCP-9045CDN, Service Manual

Search results

Summary of Contents for DCP-9045CDN

Reviews:

Brands by name

Popular brands