manualshive.com logo in svg

Brother DCP-9045CDN, Service Manual

Share
Download
Brother DCP-9045CDN Service Manual Download Page 38

Confidential 

1-19

 Error code 68 

Print Unable 68

 

Turn the power off and then back on again.

 

Fuser unit failure (The side thermistor detects higher temperature than the specified value.) 

Error code 69 

Print Unable 69

 

Turn the power off and then back on again.

 

Fuser unit failure (The side thermistor detects lower temperature than the specified value.) 

Error code 6A 

Print Unable 6A

 

Turn the power off and then back on again.

 

Fuser unit failure (The side thermistor does not detect 60°C within the specified time.) 

Error code 6B 

Print Unable 6B

 

Turn the power off and then back on again.

 

Fuser unit failure (The center thermistor does not detect 100°C within the specified time.) 

Error code 6C 

Print Unable 6C

 

Turn the power off and then back on again.

 

Fuser unit failure (The center thermistor detects higher temperature than the specified value.) 

Error code 6D 

Print Unable 6D

 

Turn the power off and then back on again.

 

Fuser unit failure (The center thermistor detects lower temperature than the specified value.) 

Error code 6E 

Print Unable 6E

 

Turn the power off and then back on again.

 

Fuser unit failure (The center thermistor does not detect temperature rising within the specified 
time.) 

Error code 6F 

Print Unable 6F

 

Turn the power off and then back on again.

 

Fuser unit failure (The center and side thermistors detect extremely high temperature.) 

Step

 

Cause

 

Remedy

 

1 

Fuser unit failure 

Replace the fuser unit. 

2 

Low-voltage power supply 
PCB failure 

Replace the PS PCB unit. 

3 

Engine PCB failure 

Replace the engine PCB ASSY. 

Summary of Contents for DCP-9045CDN












































































































































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands