Brother DCP-9045CDN Service Manual Download Page 126

Page: 126 / 491

Confidential

2-32

(2) Turn the Roller holder ASSY to the direction of the arrow 2a, push the Lift arm to the

direction of the arrow 2b and fix the Boss of the Roller holder ASSY into the hole of the Lift
arm.

Note:

Check whether the Lift arm moves by pushing the Roller holder ASSY upwards. If the Lift
arm does not move, it is not assembled correctly.

Fig. 2-54

(3) Close the Front door unit ASSY.

(4) Assemble the Separation pad spring. Put the positioning section of the Separation pad

ASSY into the spring and catch the two Hooks.

Fig. 2-55

Paper feed frame unit

Roller holder ASSY

Boss

Lift arm

<Front>

Separation pad ASSY

Hook

Paper tray

<Front>

Separation pad spring

Positioning section

Summary of Contents for DCP-9045CDN












































































































































































































































































































































































































































































































Search results

Summary of Contents for DCP-9045CDN

Reviews:

Related manuals for DCP-9045CDN

Brands by name

Popular brands

Brother DCP-9045CDN, Service Manual

Search results

Summary of Contents for DCP-9045CDN

Reviews:

Related manuals for DCP-9045CDN

Brands by name

Popular brands