manualshive.com logo in svg

Brother DCP-9045CDN, Service Manual

Share
Download
Brother DCP-9045CDN Service Manual Download Page 324

Confidential 

3-191

(3)  Remove the bind B M3x10 Taptite screw, and then remove the LV fan duct from the Frame 

unit. 

 

Fig. 3-284 

(4)  Remove the three cup B M4x12 Taptite screws, and then remove the Belt unit drive motor 

ASSY from the Frame unit. 

(5)  Disconnect the Connector from the Belt unit drive motor ASSY. 

 

Fig. 3-285 

*1 

Tightening Note: 

When tightening the screw, slowly turn it counterclockwise (in the direction to loosen the 
screw) with your hand until you feel that the screw is a little dropped in the hole. Then, slightly 
turn it clockwise (in the direction to tighten the screw) with your hand and tighten it according 
to the specified torque with a screwdriver. 

LV fan duct 

Frame unit 

Taptite, bind B M3X10 
(Tightening torque: 0.80 

±

0.1 N m)

 *1

 

<Right side> 

Frame unit 

Taptite, cup B M4x12 
(Tightening torque: 1.20 

±

0.1 N m)

 *1

 

Connector 

Belt unit drive motor ASSY 

<Right side> 

Summary of Contents for DCP-9045CDN












































































































































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands