Brother DCP-9045CDN Service Manual Download Page 424 | Manualshive

Page: 424 / 491

background image

Confidential

App. 1-9

< WSW05 >

Selector No.

Function

Setting and Specifications

1

|

3

1st dial tone detection

No. 1 2 3

0  0  0: 3.5 sec. wait
0  0  1: 7.0 sec. wait
0  1  0: 10.5 sec. wait
0  1  1: 14.0 sec. wait
1  0  0: 17.5 sec. wait
1  0  1: 21.0 sec. wait
1  1  0: 25.0 sec. wait
1  1  1: Detection (Without wait)

4

Max. pause time allowable for
remote ID code detection

0: 2 sec.

1: 1 sec.

5

6

Busy tone detection in
auto-matic sending mode

No. 5 6

0  0: No detection
0  1: Detection only after dialing
1  0: No detection
1  1: Detection before and after dialing

7

Busy tone detection in
auto-matic receiving mode

0: Yes

1: No

8 Not

used.

Note:

Selectors 5 through 7 are not applicable in those countries where no busy tone detection is
supported.

- Selectors 1 through 3: 1st dial tone detection

These selectors activate or deactivate the 1st dial tone detection function which detects
the 1st dial tone issued from the PSTN when a line is connected to the PSTN.
Setting all of these selectors to “1” activates the dial tone detection function so that the
machine starts dialing upon detection of a dial tone when a line is connected. (However, in
those countries which support no dial tone detection function, e.g., in the U.S.A., setting
these selectors to “1” makes the machine start dialing after a WAIT of 3.5 seconds.) For
the detecting conditions of the 1st dial tone, refer to WSW07 and WSW08.
Other setting combinations deactivate the dial tone detection function so that the machine
starts dialing after the specified WAIT (3.5, 7.0, 10.5, 14.0, 17.5, 21.0, or 24.5 seconds)
without detection of a dial tone when a line is connected to the PSTN.

- Selector 4: Max. pause time allowable for remote ID code detection

This selector sets the maximum pause time allowable for detecting the second digit of a
remote ID code after detection of the first digit in remote reception.
If selector 4 is set to “0” (2 seconds), for instance, only a remote ID code whose second
digit is detected within 2 seconds after detection of the first digit will become effective so as
to activate the remote function.

«
...
422
423
424
425
426
...
»

Summary of Contents for DCP-9045CDN












































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for DCP-9045CDN

Brand: CAB Pages: 263

Brand: Xerox Pages: 310

Brand: Samsung Pages: 322

Brand: Samsung Pages: 340

Brand: Samsung Pages: 349

Brand: Samsung Pages: 330

Brand: Samsung Pages: 315

Brand: Samsung Pages: 2

Brand: Samsung Pages: 2

Brand: Samsung Pages: 232

Brand: Samsung Pages: 42

SCX-6545N Series

Brand: Samsung Pages: 468

Brand: Samsung Pages: 196

SCX4521F - B/W Laser - All-in-One

Brand: Samsung Pages: 120

Brand: SPRT Pages: 28

Power Defense PD3

Brand: Eaton Pages: 4

Brand: Xerox Pages: 128

Brand: A&D Pages: 32

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands